Hot Water Heater Service Tips for Denver Homeowners

Removing Water Heater Scale

Posted by on Apr 9, 2018 in Water Heater Repair Denver | 0 comments

There are unfavorable results on house appliances, consisting of the water heater, if Denver home owners have hard water. Hard water will certainly aid make scale accumulation inside the water heater take place quicker. Scale is primarily calcium and magnesium and appears like white bits. The long-term results of scale accumulation will be to decrease the life-span of the hot water heater. In order to assist manage this taking place, this short article is going to talk about a variety of means to assist avoid it from being a trouble.

Hot Water Heater Storage Tank Drainingwater heater scale
Flushing the water tank is going to eliminate the mineral bits inside the storage tank. If one recognizes that a person water is very hard, this procedure must be done around two times a year to assist manage scale build-up. We will certainly mention the basic actions associated with doing so below, however they are suggested for academic purposes only. It would certainly be most ideal to enable us to execute a hot water heater flush at your residence.

First switch off the hot water heater’s gas or power. Shut the cold water supply shutoff so fresh water is not going into while it is being emptied and replenishing it. In order to make it a much faster procedure, open up a hot water sink faucet that is close in distance to the hot water heater system. Attach a yard hose to the drain valve, situated at the bottom of the heater, and position the other end of the yard hose either outdoors or in a floor drain for the heater to clear. The water leaving the hot water heater may be hot, so care should be taken. After the storage tank is empty, shut the drain shutoff, open up the cold water supply once again, and turn back on the gas or electrical power.

Hot Water Heater Temperature Level Setting
Heat is one reason for scale build-up happening. The hotter the water in the hot water heater is, the much more calcium and magnesium will certainly develop strong deposits on the heating elements inside the water tank. If the thermostat is positioned greater than it should be, the much faster the accumulate will occur. Though there are factors for having a high or reduced temperature level setting that greatly depend upon any type of health and wellness problems in the residence, yet we will not be entering into those information below. Producers normally pre-set and recommend a temperature level setting at 120 degrees Fahrenheit. If it is established above this, scale will certainly gather quicker. Below are a lot more ideas that will assist if one water is very hard.

Using vinegar will chemically impede scale as well. Vinegar, though a weak acid, is risk-free to utilize. It is nice to utilize vinegar in order to help cleanse the tank after draining it. Prior to reconnecting the cold water supply and turning the electrical power back on, shut the drain valve and put a gallon of cider vinegar right into the storage tank. Wait at the very least 6 hours for it to be. Undoubtedly, pick a time for emptying the hot water heater when no hot water will be required for some time. Later, open up the drain shutoff with the drain garden hose connected and allow some water run through to eliminate the vinegar. Shut the draining pipes shutoff and reconnect the power.

Water Softener
Among one of the most valuable means in order to help with hard water problems throughout the residence, not simply with a hot water heater, is to set up a water softening system. In basic terms, it will get rid of the ions dissolved in the water that create the calcium and magnesium to develop. Preserving a water softener is very easy to do. Sodium is typically the chemical used to substitute the calcium and magnesium ions, they will have to be changed periodically. The advantages to the whole plumbing system with having the ability to manage hard water are huge and could save money on requiring unexpected water heater repairs and plumbing repairs.

Get in touch with us with any questions you may have.

Aquanta Water Heater Technology

Posted by on Jun 23, 2016 in water heater technology | 0 comments

It is popular opinion, and the United States Department of Energy informs us this also, that heating water makes up for around 18 percent of the common home’s yearly energy consumption. The only other house device that makes use of more is the heating and cooling system. With the usual tank water heater that many home owners use, it is maintaining 40 to 50 gallons of water hot all day long despite when it is being made use of. Generally with this scenario, 20 to 50 % of the energy being made use of is totally thrown away. Just what are some choices to assist suppress this energy loss? The firm Aquanta, use to be called Sunnovations has been creating a practical solution for a number of years already.Aquanta Water Heater Controller

Sunnovations had a crowd-funding campaign in 2014 that did not get to its complete funding however that is alright with them for they were able to gather great deals of interest from distribution companies that has become productive with a second go around now. Aquanta is currently taking pre-orders on a new smart water-heater controller, which they believe will certainly be delivering in July of this year.

Aquanta’s CEO Matthew Carlson states that the company’s brand-new modern technology has been field tested for over a year now. It is unexpected that other companies have not begun creating a similar tool, specifically with the initial crowd-funding campaign … despite having it not succeeding for them originally. Because hot water heater usually have a life of 8 to 12 years, it is not rational to replace it when it is functioning fine, yet just does not have all the modern technology that a brand-new hot water heater might feature. Numerous brand-new hot water heater designs are making use of smart modern technology features, however there is absolutely nothing that will work with any type of current water heater to “make it smart.” Sears not too long ago released a water heater controller that does work on some of its versions, yet not all them and not with different companies hot water heaters.

The only various other tool that is just a little comparable is a hot water heater timer. However it functions like a timer, turning the heater (and only electrical hot water heater) on and off at certain times of the day; and not using smart technology.

Among the functions of the Aquanta technology is that it will “learn” just what the water usage patterns are in the residence. Most individuals tend to shower, use the dishwasher and other hot water utilizing appliances around the same time of day. The tool will function to readjust the water heater’s temperature level to meet the demand throughout peak times, and reduce the power use during non-peak times.

The Aquanta is positioned on top of a water heater. A probe is set up behind the T&P valve port and then the probe is attached to the controller. A second sensor is taped to the cold water supply. An optional 3rd probe is designed to find if there is a water leak from the water heater as well.

Last but not least, the controller has to be connected to a Wi-Fi network and homeowners will download the smartphone app on a phone. The controller links to Aquanta’s cloud-based server and begins its task of discovering the house’s hot water usage patterns. It is likewise feasible to manually enter in the water usage pattern also. So, it could manually and automatically manage the heater’s energy usage.

It is developed so DIY resident can handle the installment him or her self. If a home owner doesn’t feel up to the activity, a plumbing specialist can absolutely help the business mentions. Aquanta approximates it taking around 40 minutes for a property owner to complete the set up.

The unit will work with the majority of water heaters, no matter the energy type. It depends on the power source if it will certainly function or not. There should be an electronic ignition system, which most all newer hot water heater will have. Old gas heaters may not however. Most definitely check out the compatibility info on the business’s website right here to see.

Exactly how much energy, and translated into money, can a property owner save with the device? Below is just what Aquanta states on their site: “our data suggest that at least 20% and up to 50% of that energy in a typical home is wasted through ‘standby loss’. We are being careful to not overpromise, and have 3rd party testing underway to more specifically quantify the saving opportunity. However, our internal studies and modeling suggest that between 10-30% of water heating energy can be saved by intelligent control through Aquanta. The economic value of intelligent control of water heaters is much higher when factoring in peak or time-of-use pricing and utility peak demand reduction and similar incentives.” (read more here)

What others around the internet are saying:

Back to our blog. . .

Reasons For a Water Heater Expansion Tank

Posted by on Mar 4, 2016 in Water Heater Safety | 0 comments

No house disaster is fairly as aggravating as when a hot water heater is leaking. When the tank on a Denver CO water heater gets a leak, it can be a huge mess to clean up. For those that do not have an automated shutoff on the water heater, it will remain to take water right into the tank, until the main water line going into the tank is switched off. naturally, none of that water can be correctly heated up, since it’s all leaking out right into your basement or laundry room!

What Is a Denver Water Heater Expansion Tank?Denver Water Heater Expansion Tank

Like many materials, water expands when heats up. A traditional water heater has to heat up water many times a day, considering that hot water is generally used much in an active house several times throughout a 24 hour period of time. It is simple to not think of the amount of water that is used when every person in a family takes a bath, with cooking and washing the pots and pans, and with operating the clothes washing machine. Every single time the hot water in the tank is depleted, it needs to be refilled. That indicates that cold water gets introduced and heated up to the pre-set temperature (normally around 120-140 degrees).

The trouble, after that, is due to thermal expansion. When the heated water expands, it enhances the pressure within the storage tank. In the past, when the pressure in the storage tank developed it would simply send a little of the water back through the public water main and away from the house, thus relieving the extra pressure. Yet this strategy doesn’t still work in every area anymore since numerous public water mains have check valves that don’t permit water to turn around. This prevents backflow catastrophes in a home, yet places additional pressure on a water heater’s storage tank. This is this is how come many local communities are requiring for a water heater expansion tank to be made use of.

A water heater expansion tank is an exterior container that is connected to the water heater. When extra pressure develops inside the storage tank of the water heater, the expansion tank enables the compressed water and air to escape,considerably reducing the pressure on the water heater itself. This procedure also improves the life expectancy of the heater too.

Water heater expansion tanks are obligatory for tank installation in some areas these days. Some manufacturers will nullify the guarantee on a heater if it is not used. So look into having a water heater expansion tank setup from us. It is a great safety add on to have on any water heater, and one that has wonderful life-extending abilities. Learn more here.

Simple Water Heater Maintenance Steps

Posted by on Jan 26, 2016 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver, Water Heater Safety | 0 comments

Ready for some water heater maintenance today? It will not likely take a lot of time. . .in fact we were thinking about ten minutes. Yep, that could be as long as it will take to discuss 2 maintenance duties that every house owner can complete. The best benefit is they should help Denver homeowners with the following:Denver Water Heater Maintenance Steps

Making certain ones water heater runs for a long time, conserving expenses.
Making certain ones water heater works properly.
Making sure it works as energy efficiently as attainable, additionally saving money.

So with that in mind, let us educate you on how to invest 10 minutes once or two times a year to help prevent any water heater repairs for your Denver water heater.

Evaluating the T&P Relief Valve

The duty of the temperature and pressure relief valve, otherwise known as the T&P Valve, is extremely vital. It has the critical task of making certain excess pressure doesn’t build up within the water storage tank, which in turn guarantees the water heater does not explode. The infographic following illustrates the following ways in evaluating it. The handle should be lifted part way and then let go of it. Hopefully, it snapps back to its shut placement easily. In case it is functioning correctly, a little water might be heard going in the drain pipe beneath the lever that was just lifted and the noise of a little pressure being released might be observed. One will require a new valve when non-e of these items take place throughout the test.

Flushing Some of the Water from the Water Heater

Over time, rust and corrosion will develop on the inside of the water tank thanks to the chemical reactions taking place with the elements that are necessary to heat up water. We will not go straight into the complex chemical details in this article, but through flushing some of the water, it helps eliminate the sediment, and offer a chance to find out simply how much sediment is within the water heater.

To do a tiny flush, locate a pail underneath the drain valve, situated at the bottom part of the tank, and open the drain valve. Just drain a few gallons of water – a few buckets full. Allow for the water to sit in the last bucket for a handful of minutes. Once it settles, analyze to determine how much stuff has settled to the bottom part of the pail. If there is, if the water heater has actually not been drained for a long time (or ever), it would be best to do a complete flush of the tank to get as much of the sediment out as possible.

Have a look at how clear the water appears to be. When it doesn’t appear very cloudy only carrying out the mini flush will probably be okay. When there is a lot of sediment in the water a full flush should really be completed. If you already know it has not been flushed for years, if ever, it will be a good suggestion to drain all of it.

We will not go straight into all the measures in this article to do so, nevertheless for educational reasons, first lower the temperature. Wait at a minimum 1 hour to enable the water to cool down prior to draining it. Instead of making use of the buckets, it truly is much simpler to attach a garden hose to the drain valve and drain the water outside.

If one starts to listen to weird cracking sounds from the water storage tank, it can be an indication that there is a sizeable amount of sediment developing within. This too reduces the energy efficiency of the water heater.

Water heaters will work quite well without the need of a lot of maintenance, and a number of house owners do not accomplish any maintenance to them. But, to realize the three rewards listed at the start of the article, it is very important to at a minimum perform these 2 responsibilities. If you have any queries or think that you would like some help initially, contact us! We are always accessible to aid and to help avoid an unwelcome Denver Water Heater Repair.

Check out some more safety precautions here too.

Water Heater Repair Denver

From Visually.

Water Heater Noises

Posted by on Jan 7, 2016 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver | 0 comments

Loud banging or popping sounds from one’s water heater could indicate a number of issues. These noises may be an indicator of a severe issue with the hot water heater or they can just suggest the hot water heater is overdue for maintenance. Regardless, dealing with a loud hot water heater is usually really annoying! Thankfully the most frequent problem with water heaters is sediment build up, which is normally fairly quick and easy to get rid of and can help decrease the need for a Denver Water Heater Repair.

Sediment Deposits in One’s Denver Water HeaterWater Heater Sediment Removal Denver CO

Sediment is found in nearly all water and is especially common in residences that work with hard water. The sediment that might build up inside a water heater is composed of mainly magnesium and calcium. There are several different ways sediment deposits can produce noise. Anytime there is too much sediment, it builds up at the base of the water tank. In some cases it might trap water underneath it which causes the water to boil whenever the heater runs. The bubbles coming up from the boiling water and popping might produce unusual popping sounds. The sediment may also burn at the bottom of the tank which could cause pretty odd sounds. And, the sediment could actually get taken up into the tank then break off causing loud knocking sounds as it dives down and hits the sides.

Blocking Sediment Build Up

The simplest way to remove sediment if there is already a build up issue, is to complete a flush. This means eliminating all of the water that is in the tank and refilling it. A homeowner can complete this maintenance task, even so it may be a good idea to have a pro take care of it in case there is currently a sediment concern. That way, the specialist will be able to examine the heater to ensure there are absolutely no other issues. By having a professional come out every year to carry out a flush and give the water heater an in depth examination, will help prevent hot water heater sounds and any other issues that might come up. Lastly, putting in a water softener can absolutely help with sediment deposits because a water softener removes a lot of the sediment that is present in water.

There are several other problems that may be bringing about one’s water heater noises. Call us now to learn more and to make certain a severe water heater repair in Denver is not in the future.

Check out our post on getting rid of odors from a water heater too, next!

Getting Rid of Water Heater Smells

Posted by on Jan 4, 2016 in Water Heater Repair Denver | 0 comments

If perhaps the water coming from the faucets inside the house smells bad, there may be a problem with your water heater. There can be a few different causes of stinky water, yet the leading cause is bacteria. In the event that bacteria is getting into the water, a smell is likely to appear. Well water is typically to blame for this taking place. Even so, there are some methods a Denver homeowner can take to stop bacteria from expanding in their water and to remove existing bacteria and smells.

Protecting Against Water Heater Bacteria Growth

The most effective way to prevent bacteria from growing and resulting in unpleasant tastes and smells throughout one’s residence, is to ensure the temp is fixed at 140 degrees or higher on one’s hot water heater. In this temperature bacteria cannot grow and will die. In case your water heater temp is placed any lower than this, bacteria will not only survive but will multiply.

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Cleaning Out Hot Water Heater BacteriaDenver Water Heater Odors

In order to remove active bacteria and odors, one will have to apply harsh chemicals to kill it. Chlorine bleach is the most powerful and complete chemical cleaner to utilize. In cases where you are making an effort to clean out the water and get rid of the bacteria applying bleach by yourself, make sure you fully understand the complete method of to do so. First, the electric or gas going to the hot water heater must be turned off. After that the cold water supply must be turned off. After that, you will need to turn on one of the hot water faucets inside of the property. This lets air in the tank. Using a garden hose, empty the water from the hot water heater and shut the drain valve once all of the water is drained. Next, it’s time to pour in the bleach. One needs five oz of bleach for every gallon of water the tank can hold. Detach the flexible cold water pipe and pour the bleach into the opening. If perhaps the cold water hose is not flexible, it might be a good idea to contact a specialist. Connect the water line once more and refill the tank with water. It’s important to shut the hot water tap in the home when all the air is out of the pipe. It’s also vital to run each of the faucets which utilize hot water within the house until you’re able to smell the bleach. The bacteria that is inside the water heater can also be in piping and faucets so you must kill the bacteria in these locations as well. Allow the bleach water remain inside the tank and in the piping for nearly 3 hours not having utilizing any hot water. And then yet another flush is due. As soon as the tank is cleared for a second time, don’t put in more bleach but fill it up with water and let it stay in the tank and in the pipes for a minimum of thirty minutes. Lastly, drain out the water once again and then refill the tank with water. Allow all the hot water fixtures in the home drain until you can no longer smell bleach. Either switch the power on again or relight the pilot light and you will be good to go!

For any concerns about water odor, flushing a water heater, Denver water heater repairs, or other water heater problems, call us!

4 Indications of Hot Water Heater Failing

Posted by on Jan 4, 2016 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver | 0 comments

Water heaters typically do what they’re supposed to do and regularly go unnoticed up to the point when one needs a Denver Water Heater Repair. However, some of the issues that arise might be prevented by having frequent maintenance by a specialist. Make sure to watch your natural gas burning water heater, as some of the problems that can appear could be pricey and unsafe for family and friends and animals. Outlined in this article, we’re describing 4 signs that a gas water heater may have to be replaced.

Leaking Water

In the event that there is water on the ground around your hot water heater or leaking out of a pipe, you may want to upgrade the water heater. But, depending on just where the water is found and how much there is, you might be okay. In the event the water heater is dripping water out of a pipe and there exists a little bit of water on the ground next to the water heater, it is most likely the T&P valve. The temperature and pressure valve eliminates excess steam in the water heater, this kind of steam turns to water and will come out from the water heater through a pipe on the side of the tank. If perhaps this is the case, it is completely natural and important for the heating unit to operate correctly. You should not try to move the T&P valve and never obstruct it. If perhaps you could be worried about the quantity of water that is coming out of the pipe, contact an expert! When the dripping water is originating from the bottom of the tank, it’s pretty much undoubtedly time to get a different water heater. When the water heater heats water the metal tank expands and contracts, and this movement might result in cracks and small fractures, which will sooner or later result in leaking. When this occurs, it’s time to buy a brand new system.Water Heater Repair in Denver


Around the piping coming out of the water heater you will find pipe fittings which must be sealed tight to keep the pipe in place and keep water from leaking out of the hole. In cases where you’re noticing corrosion around such pipe fittings, water is leaking out of the hole. Even though it is not a major leak and will not likely bring about immediate damage to the hot water heater, in the event that the problem isn’t fixed, significant and pricey problems will eventually develop.

Burn Marks

In case you happen to be seeing burn marks around the base of the water heater, there are 2 potential issues. However, both happen to be very significant and each of them need an expert. One problem can be with the venting. In the event the venting is clogged or was set up incorrectly, it could cause the exhaust fumes to return into the home. This is dangerous and could lead to health issues or a fire if left unnoticed for long. Nevertheless, this may not signify you have to replace the water heater, which is a good thing. Another possible problem with burn marks might be the flue pipes inside the hot water heater are plugged. This can lead to numerous hazardous problems and, unfortunately, the water heater will need to be swapped out as soon as possible.

Orange Flame Color

Gas water heaters have got a blue flame below the tank if it’s functioning. But, if you happen to be observing that flame is an orange or yellow shade, as opposed to blue, the burner is not operating accurately and will need to be checked by a professional.

There are numerous issues that can arise with gas burning hot water heaters, although with consistent maintenance and yearly check ups, you may be able to prevent the need for an emergency water heater repair in Denver which could possibly be costly. Call us today in case you notice something uncommon with your hot water heater!

Denver Plumbing Repair

Posted by on Feb 17, 2015 in Drain Cleaning Denver, Plumbing Repair Denver | 0 comments

Carrying out plumbing upkeep is one method to conserve on your water costs. As a fact, it can assist you prevent significant residence problems which can be rather expensive in the long term. From routine drain cleaning to changing the water heater, there are various methods to guarantee that your plumbing system is in great working condition. In case the issue is past your skills, you can always give Water Heater Repair Denver a call.

Appropriate Plumbing Care and Maintenance

To be able to save water, you need to make sure that the plumbing system is constantly in great working condition. Overruning commodes and leaking pipes can really cost countless dollars. Likewise, you require to inspect for concealed leaks to ensure that you are not squandering cash on the water costs. Attempt to take an appearance at the water meter and observe if there are uncommon modifications that might be an obvious indicator of unidentified leakages.

Denver Plumbing Repairs

Carrying out small repairs is likewise extremely essential in making sure that the plumbing system is operating effectively. In case of troubles, ensure you do not postpone the repair work for this could cost a great deal of cash particularly when the circumstance gets even worse. Even with leakages, definitely be timely. To be able to not squander water, ensure to deal with right away any water damages found. In addition to plumbing repairs you may well likewise desire to safeguard your pipeline throughout cold weather condition. According to professionals, insulated pipes are less likely to come apart. This will in some way avoid from handling expensive leaking repair works.

Various Other Denver Plumbing Maintenance Tips

One method to assist in avoiding water damages due to leakages is to inspect pipes throughout the early spring and winter season. If possible, contact us to examine the plumbing system for any possible outflow. Always keep in mind that regular upkeep is one method to save water. Routine safety evaluation does not just assist in conserving water, but it can likewise be a help in decreasing the regular monthly expenses.

If you think plumbing upkeep is a bit complicated, you are completely mistaken. Prior to you even employ somebody who might look after the repair work for you, you ought to understand that easy plumbing jobs can be carried out without expert assistance. Cleaning drains is one of the upkeep jobs property owners can quickly carry out by on their own. So start the practice of staying informed of the condition of your plumbing system at home – it will pay off in the long term!

The Reasons of a Water Heater Tank Explosion

Posted by on Jan 22, 2015 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver, Water Heater Safety | 0 comments

In terms of needing to undertake upkeep on ones water heater, it is a rather minimal maintenance device.  Even so, one significant component of it must be examined routinely.  Water Heater Repair Denver wishes to pass on this safety material concerning ones water heater today.

Too much temperature if merged with tank deterioration inside of the storage tank can lead to an explosion. Any time the water temperature is under 212 degrees Fahrenheit, one shall be protected from an explosion, though there is a risk of scalding at that temperature.  However, if the water temperature is over 212 degrees, water changes into steam, which will enlarge to 1,700 times the space it takes up as water. This is the time an explosion can happen.

Cautionary Signals of a Water Heater ExplosionHot Water Heater Repair Denver

The leading sign is if one goes to get hot water from a faucet and only steam comes out.  Without delay shut off electric power if one possesses an electric water heater.  If one possesses a gas hot water heater, shut off the gas valve on the water heater.  Next, give us a call to come evaluate the scenario.

Minimizing Potential Water Heater Dangers

The most essential routine maintenance endeavor having a water heater is to examine the pressure relief valve, also known as the T&P valve, on a usual schedule.   This valve helps control the pressure accumulation on the interior of the water storage tank to avert a threatening increase in temperature and overpressure.

Be careful, the water release with a T&P valve is often rather hot. If you do not feel safe evaluating the valve contact us.  In addition, executing any kind of fixes to the valve should really be executed by a expert plumbing repair provider.

How to Test the T&P Valve

Clear the space near the overflow pipe and floor drain.
Lift up the test handle for about 5 seconds or until the water runs clean.
Let go of the handle.
If the T&P valve keeps on running with water, raise the handle up and down rapidly to have it reseat itself.  One may need to do this a handful of times.  IF it has not been tested for a while, it might be difficult to raise it at first.  Avoid using an excessive amount of force, although could need to make use of just a little.
If the T&P valve continues to have water coming out, it should really be changed.

Additional points to watch out for are rust on the stem of the valve.  If there is any water seeping out of the valve stem or out of the drain valve.

Interested in far more strategies?  Look at Hot Water Heater Repair Denver’s additional articles right here:

Denver Water Heating Savings Advice

Water Heater Blankets Save on Heat Loss

From around the Web:

The Aquanta smart water-heater controller promises to slash your energy bill

Home maintenance checklist: Fall

Leaking Water Heater Pressure Relief Valve

Posted by on Dec 9, 2014 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver | 0 comments

The pressure relief valve of ones Denver water heater has an essential task – ensuring the water heater tank does not explode. So with that in mind, we wish to see to it house owners know ways to best look after it. They will certainly leak when the valve breaks or when the water storage tank pressure gets higher then the relief point.Hot Water Heater Repair Denver

We suggest that a minimum of two times a year, property owners test to make sure the pressure relief valve, or T&P valve as we will call it, is working appropriately. All one needs to do is raise the handle for a couple of seconds and release it. It must snap back to its initial position. When it is raised, one could hear the noise of pressure being released , just like the noise of air coming out of a tire pump when being disconnected. Likewise, a little water may come out too. Both are regular. If the valve has not been tested for a number of years, it may stick at first too.

However, if the handle does not snap back, or if it continues to leak a little water, that is not typical. If it still leakages some, raise the handle a couple of more times to see if it will re-seat itself. You may want to wait a day or so it see if it re-seats itself before presuming it needs to be replaced.

We would prefer to manage any T&P valve replacements for you, so though hot water heaters are normally relatively upkeep free, there are some safety preventative measures one ought to bear in mind. With that here is an overview of a pressure relief valve replacement.

1. The gas to the water heater has to be turned off, or the breaker for an electrical water heater.
2. The cold water cut-off valve has to be closed next.
3. The valve below the T&P valve needs to be opened to drain a little water in order to relieve some of the pressure in the storage tank.
4. The overflow pipe of the T&P valve needs to be removed. It might need to be cut off if it is soldered or firmly glued.
5. The pressure relief valve needs to be unscrewed with a pipe wrench.
6. Wrap the brand-new T&P valve with Teflon tape and screw it back in place. Make sure the overflow pipe opening is positioned away from the storage tank.
7. Reattach the drain pipe, also utilizing new Teflon tape.
8. Turn the water back on, and examine your work for any leaks.

The following video provides a summary of this process:

Winterizing Ones Water Heater

Posted by on Nov 10, 2014 in Water Heater Repair Denver, Water Heating Savings | 0 comments

We enjoy to pass along ideas on how to conserve on energy expenses at home. Here are some of the best ways to get ones water heater ready for the winter.

A simple way to inspect ones water heater’s need for insulation is to put ones hand near to or on the outside of the storage tank. It is feels warm, insulating the tank is advised. Throughout the winter season this heat loss you just felt can build up. Conversely in the summertime, if the water heater is located inside the house, and not in a garage, it can add heat to the space that you are attempting to cool. The heat you feel is obviously heat being lost. If it is not warm at all that is a great sign that the tank’s internal insulation is in respectable shape. Brand-new water heating systems are being made with a nice quantity of internal insulation today. You can examine the manufacture’s label to see exactly what the R-value is. If it R-24 or greater, one should be in terrific shape without having to include an insulation blanket to the water heater.

Denver Water Heater Blankets

The treatment for this heat loss is with a water heater blanket or wrap. First check with your local energy company, for some have insulation kits at decreased costs for homeowners. A hot water heater blanket will can be found in various sizes depending on the gallon size of the storage tank. The higher the R-value, the more insulation power it has. We would recommend getting at least an R-11.

The blankets are easy to set up. They will have insulation tape to finish the joints of the blanket. The shinny or vinyl side goes on the outside.

For gas water heaters, wrap it all around, leaving the top flue unwrapped, and do not wrap around the controller on the bottom. Likewise, do not wrap the T&P valve handle, or the bottom of tank for that is where air enters. For electric water heaters, the top can be wrapped for there is not an exhaust flue, however do not wrap the heating-element access panels.

Water heater blankets will last quite a long period of time. You could even have the ability to utilize the very same one once again whenever the water heater is replaced, providing it’s the very same size storage tank.

Water Heater Pipe Insulation

There are 2 types of pipe insulation that should be used for a water heater. For pipes that are within 6 inches of the water heater exhaust flue, fiberglass insulation wrap ought to be made use of and should be attached with either high temperature aluminum tape or wire. Foam insulation sleeves can be used for all the pipes that are additionally away then 6 inches of the flue then.

The United States Department of Energy suggests that house owners insulate at least 6 feet of the pipe coming into and out of the hot water heater. This can increase the temperature level at the faucets 2 to 4 degrees and conserve money on heating. We likewise recommend wrapping both the hot and cold pipes too simply due to the fact that every little bit helps.

Energy Savings from Denver Water Heater Insulation

Insulating an inefficient water heater can cut the cost of running that heater by 5 % to 10 %. Depending on the model, that can save anywhere from $5 to $20 per year, meaning that a water heater blanket can be paid for in 1 to 4 years. Adding insulation could minimize standby heat losses by 25 % – 45 % and save about 4 % – 9 % in water heating expenses.

What others round the web are saying:

Denver Water Heating Savings Advice

Posted by on Nov 7, 2014 in Water Heater Repair Denver, Water Heating Savings | 0 comments

Faucet aerators and low flow shower heads easily conserve water, and water conservation implies house energy savings for you.

Bathroom and kitchen faucet aerators are easy to add to ones faucets. The wire screens just screw in and will blend air into the water flow, think of it as rationing the water flowing out of the faucet.Water Heater Repair Denver

When initially introduced the preliminary purpose was to merely lower the flow rate or water stream in order to remove sink splashing.

However, with the increasing interest in water preservation, house owners and companies that are looking to save on energy usage, are becoming more interested in the water saving potential of faucet aerators.

In terms of ones Denver water heater, aerators do not just conserve water, they likewise assist in lowering the natural gas and electrical energy cost of water heating. Aerators paired with water saving shower heads can lower the typical residences hot water use by as much as 50 percent.

Both water conserving gadgets are exceptionally inexpensive and extremely simple for homeowners to install.

Low flow aerators can be added to nearly any basic faucet. Look along the tips of ones faucets to see if there are threads along the inside. Even many older restroom and kitchen sink faucets are pre-threaded.

If one already has older aerators on ones faucets, they can be removed by hand or with a wrench. The flow rate (which is determined in gallons per minute or gpm) ought to be imprinted along the side. More recent faucet aerators can substantially decreased flow rates even additionally than older models and all without reducing the water pressure.

Kitchen Aerators

Kitchen faucets normally demand higher flow rates than a bathroom faucet. Because of this, aerators with minimum flow rate of 1.5 gpm is extremely advised for conserving water. However kitchen faucets without aerators can use as much as 3 to 5 gallons of water per minute.

A new design of aerators have swivel pivots that permit a circular or turning motion which comes in useful when cleaning ones kitchen sink. Those who clean dishes by hand could find a swivel aerator with a shut off valve much more ideal.

Bathroom Aerators

Bathroom aerators generally are chrome plated or brass. They supply a more direct and pressurized spray than the majority of kitchen aerators. And bathroom aerators usually cost even less, varying anywhere from $2 to $5 each.

Bathroom faucets without these attachments can utilize anywhere from 2 to 4 gallons of water per minute. New low flow restroom aerators use as low as 1 to.5 gallons per minute and all without lowering water pressure.

Always Remember to Keep Aerators Clean

The wire screens can get obstructed with sediments and other mineral deposits after months or years of consistent use. Regularly take them off for a cleaning. This will resolve possible water pressure troubles along with prevent future faucet leaks.

Low Flow Shower Heads

Installing low flow shower heads is really among the most cost effective things any house owner can do to conserve water. 30 % to 40 % of American homes today have conventional restroom shower heads installed which make use of as much as 5 to 7 gallons of water per minute.

The low flow shower heads currently on the market are not the old flow limiting models of the past. A brand-new water saving shower head can significantly minimize ones water use and enhance water pressure at the same time.

Now water saver shower heads make use of air chambers or jet streams to rapidly blend air into the water flow. The streams and chambers allow the shower heads to use substantially less water, and also increase water pressure for that unwinding massage sensation.

In the past few years some designs have successfully lowered water flow rates even lower than the federal guidelines. Some low flow designs make use of as low as 1 gallon of water per minute.

A few of the best shower heads permit one to stop briefly warm water while in the shower. These shower heads are extremely practical and they can help one save much more by using less warm and warm water while bathing.

This gives ones hot water heater a much deserved break, which in return translates into lower water heating cost.

Check out our other tips in our blog here too!

Denver Water Heater Installation Costs

Posted by on Nov 6, 2014 in Water Heater Replacement Denver | 0 comments

The typical life-span of a conventional tank-style natural gas water heater or electric water heater is about eight to 12 years, so the prospect of having to replace a water heater is an usual home improvement. Water Heater Repair Denver has discussed a few of the factors that affect the installation expenses here.

The costs to set up a brand-new Denver hot water heater do range in cost depending upon the company performing the installation, and depending upon the type of water heater installed. For instance, energy-efficient tankless water heaters do cost more to set up, though those costs can be recouped over the life of the device. There are online tools that will provide a quote on water heater installation expenses for the part of the country one resides in.

Water Heater Installation Cost Factors

Without seeing the place that ones water heater will be installed or replaced, it is difficult to offer a specific idea of the cost. If it is a water heater replacement, and is being changed with a similar sized and style of heater, the installation expenses will certainly be really affordable. If one is changing to a different kind of water heater, like from an electric to a gas or tankless device, the installation expenses will certainly be greater because we will need to possibly add gas lines and connections.

Another consideration is to see to it a replacement water heater will be up to code with what is needed now, not with what the code was ten to twelve years ago when the present water heater was installed. Also, there is the potential that the existing water heater was not up to code when it was initially set up either! Which can be the case if a previous property owner did the installation him or herself.

Because of the safety factors involved with water heating units, it is always best to have a professional plumbing company perform the installation. One, most homeowners will not have an idea of exactly what the code requirements are. One risk factor is that electric water heaters utilize 240 volts of electricity, which is extremely dangerous to work with if not experienced in doing so. Water Heater Repair Denver CO spends a lot of time taking care of incorrectly installed water heaters.

Another safety concern with not having an expert install ones water heater is working with natural gas lines. This, too, can be unsafe, and a circumstance where there can not be any leakages.

A final safety issue is with effectively venting the exhaust to ensure carbon monoxide leaves the home. Carbon monoxide poisoning occurs more frequently than most people think, and it is best to make certain one has a carbon monoxide gas detector in ones home too. According to the Centers for Disease Control, unintended carbon monoxide poisoning causes 400 deaths each year and 20,000 visits to the emergency room.

Other factors to consider with setting up is ensuring it is plumbed correctly, there is enough clearance and ensuring drip pans are equipped, if required.

Water Heater Blankets Save on Heat Loss

Posted by on Nov 1, 2014 in Water Heater Repair Denver | 0 comments

Water heater wraps or blankets are probably the most cost effective means of all the energy preservation measures. There are no other preservation measures that has the life span, expense and and payback that the water heating system wraps have suggests Water Heater Repair Denver.

These insulation jackets last as long as the water heating unit and if you are as frugal, you can utilize the old one and put it on the brand-new one, if it will fit. Average life of a water heating unit, 10 years. Expense $30. Money saving differs from $30 to $50 annually, depending upon the effectiveness of the water heating unit.Water Heater Repair Denver

What water heater wraps do is maintain the temperature level of the water longer. In shorts, the heating elements or gas do not need to come on as typically when a insulation coat is set up. Besides the fact that it saves you money on your energy expenses, it will, without question, prolong the life of the water heating unit. To show this is you and your neighbor work at the very same area, 10 miles away. With all else being equal except that you drive to work at 25 mph and he/she does it at 40 mph. He/she gets to work or home in 11 minutes and it takes you 12 minutes. As far as the automobiles are worried, which automobile will make use of more gas for the very same distance? Which car will require even more maintenance? Which vehicle will last longer?

This applies to a water heater in much the same means. The typical family really only utilizes warm water a bit more than a hour. For instance, it might take you 45 minutes to clean clothing, but it just takes 2 minutes for the washer to full of warm water. Your youngsters might take 45 minute showers, they are just making use of the water in the shower at most 15 minutes. Try staying under a hot shower for more than 15 minutes, you will come out looking like a prune. Exactly what this suggests is that for more than 22 hours a day, the water heating unit just maintains the temperature level of the water. So let’s say you are excessive with hot water, let’s double it, it is still more than 20 hours a day just preserving the temperature. Plainly the huge majority of the cost to run a water heater is preserving the temperature of the water when no-one is making use of hot water.

A water heating system without the insulation coat comes on to maintain the temperature level typically 4 times an hour. One with the insulation jacket 3 times an hour. On top of that the water heating system without the jacket will certainly remain on for a longer period than one with the coat. Given that all heating elements produce hostile environments, regardless if it is electric or gas, the more times per hour and the longer the heating elements remain on, the much shorter the life span of the water heater. You will benefit from the setup of the insulation jacket but who will certainly not benefit are individuals who install them for a living and the makers.Let us know at Water Heater Repair Denver if you need assistance with sizing or choosing the best one for your home.

Here is another video on how to install a water heater blanket:

Water Heaters and Transite Asbestos Flues

Posted by on Jun 13, 2014 in Water Heater Repair Denver | 0 comments

For those that reside in an older house, here is some details from an article we recently read and feel obliged to pass along to our Denver Water Heater Repair customers. Transite asbestos used to be used in venting gas appliances, like water heaters, years ago. Undoubtedly, it is not made use of any longer, however in the following short article, the Minnesota home inspector, Reuben Saltzman, found that within the vent flue was partially obstructed from the asbestos flaking off into the flue.Water Heater Repair Denver

When inspecting one home in particular, Saltzman noticed “the top of the flue liner had fallen off the chimney, and the interior had collapsed in on itself, causing the water heater to backdraft. . . the interior had flaked apart and completely blocked the flue.  When the happens, the exhaust gases can’t escape, so they go back into the home.  There was heavy rust staining on top of the water heater, which is a telltale sign that the water heater backdrafts.  It doesn’t get much more obvious than that.” (read more…)

Saltzman suggests to fix this, do not continue to use a gas water heater on the very same flue. Install either an electric one or a powervent water heater with a new vent to the outside of the house. With a few of the older homes with this sort of flue set up, the flues are still in good shape. It could be ok to still utilize them if an inspection shows they are in tack and not flaking apart. Nevertheless, if not, absolutely block them off and install an electric water heater or create brand-new venting for a gas hot water heater.

There are some nice photos in this video of these asbestos flues:

Denver Water Heater Carbon Monoxide Poisoning Prevention

Posted by on Jun 6, 2014 in Water Heater Repair Denver, Water Heater Safety | 0 comments

We have just recently seen a few news reports about carbon monoxide poising being connected back to a water heater as the source and so felt it important to share some about that possibility today. Yes, any nonrenewable fuel source burning device produces this fatal gas. Including water heaters. Nevertheless, with the proper setup of the water heater, together with periodic maintenance, and a working carbon monoxide detector in the house, one can sleep securely.

Causes of Carbon Monoxide PoisoningWater Heater Repair Denver

Carbon monoxide gas (CO) is a colorless, odor free gas that is a bi-product of the burning of a nonrenewable fuel source like wood, gasoline, coal, natural gas, or kerosene. Breathing in carbon monoxide gas fumes not only avoids oxygen from being used appropriately by the body, but likewise triggers damage to the central nervous system. Individuals with existing wellness problems such as heart and lung illness are specifically vulnerable, as are infants, kids, pregnant women, and seniors.

Sources of Carbon Monoxide Gas

The winter heating period is when a majority of carbon monoxide exposures take place due to the use of unvented supplemental heaters. An unvented supplemental heater is a sort of space heater that uses indoor air for heating and vents the gases produced in the heating procedure out into the house. A lot of heaters of this type use kerosene or natural gas for fuel. While newer designs have oxygen sensing units that shut off the heater when the oxygen level in the area falls below a certain level, older models do not have such safety functions. Because of these security troubles, unvented space heaters have been banned in numerous states. Other sources of carbon monoxide are malfunctioning cooking equipment, tobacco smoke, clogged chimneys, automobile exhaust, malfunctioning furnaces and gas clothes dryers, wood burning fireplaces, and a water heater.

Signs of Carbon Monoxide Gas Poisoning

Below are the most usual symptoms of carbon monoxide poisoning however they are not constantly the very same for every person who has been exposed and sometimes resemble having food poisoning or the flu. A physician can assist in figuring out for sure.

nausea and vomiting
rapid heart beat
cardiac arrest
loss of hearing
fuzzy vision
loss of consciousness or coma
respiratory failure

Defense By Correct Gas Appliance Venting

The CDC provides the following info on avoiding CO2 poisoning by making sure ones appliances are vented properly.

  • All gas appliances must be vented so that CO will not build up in your home, cabin, or camper.
  • Never burn anything in a stove or fireplace that isn’t vented.
  • Have your chimney checked or cleaned every year. Chimneys can be blocked by debris. This can cause CO to build up inside your home or cabin.
  • Never patch a vent pipe with tape, gum, or something else. This kind of patch can make CO build up in your home, cabin, or camper.
  • Horizontal vent pipes to fuel appliances should not be perfectly level. Indoor vent pipes should go up slightly as they go toward outdoors. This helps prevent CO or other gases from leaking if the joints or pipes aren’t fitted tightly.  (read more…)

It is absolutely important to have CO2 detectors in the home. The Colorado State University Extension provides the following tips when choosing a CO2 alarm.

  • Some inexpensive alarms consist of a card with a spot (spot detectors) that changes color in the presence of CO. The absence of an audible signal does not meet UL or IAS requirements for alarms, so these devices do not provide adequate warning of CO.
  • Some CO alarms have a sensor that must be replaced every year or so. The expense of this part should be a factor in purchase decisions.
  • Battery-operated alarms are portable and will function during a power failure, which is when emergency heating might be used. Batteries must be replaced, although some alarms have long-life batteries that will last up to five years.
  • Line-powered alarms (110 volt) require electrical outlets but do not need batteries. They will not function during a power failure. Some line-powered alarms have battery backups.
  • Some alarms have digital readouts indicating CO levels. Alarms with memories can help document and correct CO problems.  (read more…)

The following video offers some good safety ideas for water heaters.

Not to scare anyone, however we likewise wanted to include the following video of a water heater set up that is not working properly and is hazardous.

Please see a medical professional quickly if you believe that you or a member of your household could have carbon monoxide gas poisoning. Water Heater Repair Denver can not stress enough the need of making certain a professional plumbing repair business services and installs any water heater equipment in your house or business.

Water Heater Venting Options

Posted by on May 13, 2014 in Water Heater Repair Denver | 0 comments

The following concepts about proper Denver water heater venting from us here are shared in order for homeowners to have a general understanding of how the different kinds of venting work. They are not intended to be how-to directions for property owners to perform themselves. The training and licensing of a professional plumbing repair work service professional is exceptionally essential.

In terms of venting, water heaters are usually vented in two methods; direct vent water heaters and power vent water heaters. So what is the leading distinction between the 2 styles of water heaters? A direct vent water heater vents the combustion gases created from the water heater’s burner directly to the environment, while a power vent water heater eliminates them with the aid of a powered venting fan.

This video gives some tasks to perform to help see if your water heater is currently properly vented:

Direct Vent Denver Water Heaters

For direct vent water heater, the heat created from the combustion procedure is made use of to warm the water. The exhaust gases are then moved to the beyond the house through the exhaust pipe or chimney.

With direct venting, it operates with the theory that heated air is lighter than cool air and will then rise normally due to the difference in buoyancy between the hot and cold air. This is a good basic system that works well when the exhaust gases can be vented vertically. No additional power is needed, and in turn the general hot water heating costs are lower.

The following video explains in more detail the details of a direct vent system:

Power Vent Denver Water Heaters

Power vent water heaters uses a fan or blower to aid in the removal of exhaust gases from the hot water heater. For houses that don’t have access to a vertical vent or chimney, power vent water heater could be the best choice. With the use of a fan or blower, exhaust gases can be pressed with horizontal exhaust vent pipes.

The main benefit of a power vent water heater then is the capability to locate the water heater away from a chimney. Or if there is no chimney readily available, to conserve money by horizontally venting it to the outside through affordable venting pipe instead.

The downsides of a power vent system vs. a direct vent heater are that power vent heaters will cost more at first because of the additional devices (fan/blower) required for the install. Also, one will also have to run a power line to the fan. This too, will include to the cost.

An additional disadvantage is that the blower portion of the water heater will require electricity to operate. This will raise the hot water heating expenses throughout it’s life time, though not that much.

And lastly, the fan noise can be heard running when the hot water heater is running. While it’s most likely only a small concern, it’s something that ought to be seriously considered. Appropriate installation can help to eliminate, or at the very least decrease most of this.

Though there are some differences between the two types, it really depends on a home’s specific situation, in regards to the where it will be installed, and the ability to have access to a vent path to the outside of the home.  Denver Water Heater Repair recommends taking a look at the ENERGY STAR info right here too in terms of the various energy efficiency ratings for the different types of sorts of heaters.

Enhanced by Zemanta

Preventative Water Heater Repair

Posted by on Apr 1, 2014 in Water Heater Repair Denver, Water Heater Replacement Denver | 0 comments

Most don’t ever think about the condition of their water heater Water Heater Repair Denver knows. Justifiably so, as long as it is functioning smoothly. Nonetheless, a little water heater maintenance can go a long way toward reducing the number and frequency of repairs, and really helps to extend the life of the heater, avoiding early replacement. Learn how preserving your water heater can affect its life-span and give you less stunning moments of cold water.

A Healthy Denver Water HeaterWater Heater Repair Denver

While it is difficult to identify specifically how long a water heater ought to last, a properly serviced, quality water heater can last 8 – 10 years. Naturally, lots of factors will impact the life-span, consisting of electrical energy irregularities, the quality of the water heater, and the mineral density of the water. Routine water heater maintenance can also reduce electric expenses by having it function more efficiently

Among wears out a water heater is mineral buildup. A great deal of cash is spent replacing heating elements and entire tanks, when some upkeep periodically would help to prevent this expenditure from happening. A healthy water heater is one that is insulated, clean, and without electrical wiring problems.

Issues with ones water heater typically become clear: A hot water faucet fails to summon hot water, you see leaking or puddles near the water heater, or the tank emits weird gurgling or popping noises. These are a few indication telling you when your hot water heater needs replacing.

It would be nice to understand before your water heater springs a leak and triggers a trouble or worse yet damage to your house. If you identify you have some of the early caution signs you will have time to evaluate your options of sizes and models and pick a certified installer rather than rushing to discover a replacement water heater on a Friday afternoon or worse on a weekend.

Right here are some signs that you may be all set for a brand-new hot water heater

Age: On average, your gas hot water heater should last anywhere between 8 to 12 years, while an electric model will last a bit longer at 10 to 15 years.
Discolored Water: When you utilize your hot water tap, does the water look a bit tinted? If so, there may be rust in your water heater, which is a possible indication your hot water heater is revealing signs of wear and may begin to leak.
Banging or Popping: When there is a accumulation of hard water sediment inside the storage tank,it could could sound like explosions. These noises are caused by the difference in water temperature inside the tank as new cold water mixes with the heated water of the tank.
Moisture: Look around the base of the water heater for moisture, for this might be a symptom of a slow-moving or periodic leak.
Cold Water: An unanticipated cold shower is not only bad way to begin your day, but of a hot water heater that requires to be looked into.
Major Water Leaks: It’s time to call us now.

Enhanced by Zemanta

Denver Thanksgiving Energy Conservation Tips

Posted by on Nov 21, 2013 in Plumbing Repair Denver, Water Heater Repair Denver | 0 comments

We will not bore you with the typical trite opening to a Thanksgiving post … Water Heater Repair Denver really just desires to share this infographic on saving energy this Thanksgiving weekend.

There are lots of means to save money on energy utilized in the kitchen while preparing your feast that are added here. Also, with all the heat produced from the kitchen area and the additional body heat in the home, one can quickly turn the thermostat down too!

Water Heater Repair Denver

Now back to exactly how we opened the post … yes Water Heater Repair Denver likes Thanksgiving and are very grateful for numerous things. We didn’t desire to suggest we are not concentrated on the spirit of the holiday. It most definitely a time to reflect on all the blessings we have and can offer to others! Enjoy!

You can also view this infographic at or

Denver Water Heater Safety Precautions

Posted by on Nov 13, 2013 in Gas Water Heater Repair Denver CO, Water Heater Repair Denver | 0 comments

Appropriately keeping ones water heater is crucial not so it works to its complete potential and can conserve some energy cash, but for security concerns too. Yes, it can explode – it does not happen too often for homeowners, but obviously this is something that we do not want to have take place to you!

Water Heater Repair Denver has put together a presentation on the potential dangers and what the prescribed maintenance is to prevent dangers from occurring.

Denver Water Heater Repair’s Safety Tips